Resetting Your Holosun EPS Carry Red Dot

Wiki Article

Performing a complete reset on your Holosun EPS Carry red dot is a relatively simple procedure, and can be useful for troubleshooting issues or preparing the optic for sale. To begin, locate the tiny recessed reset button on the left side of the device. You’ll need a specialized tool, such as a punch, to depress the button. With the Holosun EPS Carry enabled, gently depress and hold the reset button for approximately 5-7 seconds. You should see the reticle briefly blink, indicating the reset process has begun. After the reticle reappears, the Holosun EPS Carry will be reset to its original factory settings, erasing any previously programmed configurations. Remember to re-zero your optic after completing this procedure.

Rebooting Your Holosun EPS Carry Red Dot: An Easy Guide

Need to fix a glitch or set up your Holosun EPS Carry red dot for reuse? A factory reset can often be the solution. This brief guide will walk you through the process of clearing your EPS Carry to its original configuration. Essentially, it clears all here user choices and returns the optic to the way it was when it was manufactured. Don't fear – it's a quite simple operation and won't harm your sight. Just stick with these instructions carefully. We'll cover the button sequence needed to trigger the reset, emphasizing a cautious approach to verify a successful outcome. This way is perfect for preparing for resale.

Rebooting Your Holosun EPS Carry: Original Reset Procedures

Sometimes, your Company's EPS Carry optic might exhibit strange behavior – perhaps the reticle isn’t appearing as it should, or the settings seem muddled. In such cases, performing a original reboot can often correct the issue. This process returns the optic to its original state, effectively erasing any custom settings you’ve configured. To initiate the reboot, first, ensure the optic is powered. Next, depress and hold both the left and port buttons simultaneously. You should observe the reticle momentarily pulse, signifying the reset process is underway. Drop the buttons once the reticle disappears. Your EPS Carry is now reverted to its factory configuration and ready for customization. Check your EPS Carry user manual for precise information and any applicable safety guidelines before performing this procedure.

Initiating a Holosun EPS Carry Original Reset: Your Easy Process

Need to reinitialize your HoloSun EPS Carry sight to the original configuration? A factory reset can be necessary for troubleshooting issues, transferring the optic, or simply starting anew. Here's a detailed guide to perform this action. First, ensure your EPS Carry is powered off. Then, depress and keep the port switch while simultaneously pressing the fire pad. Continue holding both pads until the aimpoint briefly blinks – this shows the reset is taking place. Finally, release both buttons and allow the sight to reboot. Your EPS Carry should now be returned to its factory state. Note that this will erase any custom settings you've configured.

Restoring Your Holosun EPS Carry Red Dot Sight

If your sight EPS Carry reflex sight is acting oddly, displaying incorrect behavior, or you simply want to reset all user settings, performing a default reset can often resolve the issue. The procedure is relatively simple and only takes a few seconds. Begin by locating the recessed reset switch on the underside of the sight. This is usually covered by a small silicone insert, which you will need to remove using a small tool like a paperclip. Once you've revealed the feature, depress and maintain it down while simultaneously activating the sight. Continue holding the feature for approximately several minutes until the dot quickly fades, indicating the reset is done. Release the button, and your EPS Carry should now be operating with its factory settings.

Performing a Sight EPS Carry Original Reset Process

To resolve unexpected behavior or restore your Holosun EPS Carry to its original settings, a factory reset can be beneficial. Generally, the reset necessitates a specific sequence of button presses. Begin by ensuring the optic is powered on, then swiftly press and hold both the "On/Off" and "Brightness Up" buttons at the same time for approximately five to seven seconds. You should observe the reticle briefly go dark, indicating that the reset is underway. Once the reticle fades, let go of the buttons. The EPS Carry will then restart to its default state. It’s vital to review the official Holosun manual for the most accurate instructions, as minor variations may apply depending on the specific firmware version. Subsequently, verify the reticle brightness and other settings, and adjust as needed.

Report this wiki page